DYNAMIC ANALYSIS AND QUANTITATIVE FAULT CHARACTERISATION OFA THREE-PHASE INDUCTION MOTOR USING d-q TRANSFORMATIONAND MATLAB/Simulink
Keywords:
induction machine , d-q transformation , Matlab/SimulinkAbstract
Three-phase induction motors are widely used in industrial drive systems, where electrical faults can produce significant disturbances in current, electromagnetic torque, and rotor speed. This study presents dynamic modelling and quantitative fault characterisation of a three-phase induction motor using the d-q transformation and MATLAB/Simulink. The developed model was used to investigate the motor under no-fault, three-phase symmetrical fault, and unsymmetrical line-to-ground (L-G), line-to-line (L-L), and double line-to-ground (L-L-G) fault conditions. The dynamic responses were evaluated using peak stator current, RMS stator current, minimum rotor speed, percentage speed reduction, minimum electromagnetic torque, peak-to-peak torque variation, and phase current imbalance. Under the no-fault condition, the motor attained a steady-state speed of approximately 1800 rpm. The three-phase fault resulted in a small speed reduction to approximately 1734.14 rpm and a minimum electromagnetic torque of −71.71 Nm. The L- G fault produced a comparatively smaller speed reduction to approximately 1764.10 rpm, although significant current and torque disturbances were observed. The L-L fault produced the highest peak stator current of approximately 226.62 A and the largest peak-to-peak torque variation of 319.49 Nm, while the L-LG fault produced the phase current imbalance of 70.69%. The results demonstrate that fault severity is dependent on the performance metric considered and that no single dynamic variable is sufficient to comprehensively characterise induction-motor fault behaviour. The proposed quantitative fault characterisation provides useful complementary dynamic indicators for quantitative comparison of induction motor fault responses and provides a simulation-based foundation for subsequent condition monitoring and fault classification studies.
Published
How to Cite
Issue
Section
How to Cite
Similar Articles
- Apena W. O., Adebanjo I. A., IMPROVEMENT OF MEDICATION DELIVERY TRICOPTER STABILITY USING ACKERMAN METHOD , FULafia Journal of Science and Technology : Vol. 5 No. 2 (2019): Fulafia Journal of Science and Technology (FJST)
- Usman Mohammed Yusuf, Dr. Mbah Moses A., Alaku A. Abimiku, On Signed Full Transformation Semigroup of a Finite Set , FULafia Journal of Science and Technology : Vol. 9 No. 1 (2025): Vol. 9 No. 1 (March, 2025): Fulafia Journal of Science and Technology (FJST)
- Ahmed Kasimu Dahiru, Ifeanyi Christopher Eke, Muhammad Dahiru Liman, A Comparative Analysis of Machine Learning and Deep Learning Models for Transportation Data Analytics Using CRISP-ML Methodology and Power BI. , FULafia Journal of Science and Technology : Vol. 11 No. 1 (2027): Fulafia Journal of Science and Technology (FJST)
- Omotainse P. O., Agidi G., Dairo O. U., Benjamin T. A., DESIGN AND FABRICATION OF A BRIQUETTE MAKING MACHINE , FULafia Journal of Science and Technology : Vol. 4 No. 2 (2018): Fulafia Journal of Science and Technology (FJST)
- Ibrahim G. Bassi, Moses Anayo Mbah, Ekojah Joshua, A STUDY ON CAYLEY DIGRAPHS OF THE FULL TRANSFORMATION SEMIGROUP WITHRESPECT TO GREEN'S D-CLASSES , FULafia Journal of Science and Technology : Vol. 11 No. 1 (2027): Fulafia Journal of Science and Technology (FJST)
- Samuel Oluyemi Owoeye, Folasade O. Durodola, Adetoro Taofeek, Babatunde Bisiriyu, Mahrufdeen Adegbenro, REAL-TIME IDENTIFICATION OF MAIZE PLANT AND WEEDS USING MACHINE LEARNING MODEL IMPLEMENTED VIA YOLO v5 , FULafia Journal of Science and Technology : Vol. 8 No. 2 (September, 2024): Fulafia Journal of Science and Technology (FJST)
- Moshood A. Hambali, Beatrice A. Ayati, Yinusa A. Olasupo, Mu’awuya Dalhatu, Adesina A. Akinyemi, AN INTELLIGENT FEATURE-OPTIMIZED FRAMEWORK FOR DDoSATTACK DETECTION USING SVM and XGBOOST , FULafia Journal of Science and Technology : Vol. 10 No. 1 (2026): Fulafia Journal of Science and Technology (FJST)
- Ugbene I. J., Mbah M. A., ON THE COMBINATORIAL PROPERTIES OF NILPOTENT AND IDEMPOTENT CONJUGACY CLASSES OF THE INJECTIVE ORDER-DECREASING TRANSFORMATION SEMIGROUP , FULafia Journal of Science and Technology : Vol. 1 No. 1 (2015): Fulafia Journal of Science and Technology (FJST)
- Aderinlewo A. A., Biobaku O. L., Adepoju V. O., DESIGN AND CONSTRUCTION OF A MOTORISED JUICE EXTRACTOR , FULafia Journal of Science and Technology : Vol. 4 No. 2 (2018): Fulafia Journal of Science and Technology (FJST)
- Usman Mohammed Yusuf, Babayo A. M., Mbah M. A., Products of Nilpotents in Partial Transformation Semigroups using Digraphic Paths and Chains , FULafia Journal of Science and Technology : Vol. 9 No. 1 (2025): Vol. 9 No. 1 (March, 2025): Fulafia Journal of Science and Technology (FJST)
You may also start an advanced similarity search for this article.
